navileft-adverts.html
 |
Get Your
WineMaker
Beginner's Guide |
|
 |
Got Questions?
Get the Winemaker's Answer book! |
|
|
 |
 |
| How do I allow for suspended solids when taking hydrometer readings? |
| |
| |
Dear Wine Wizard,
I have been making wines for more than 20 years, but I have a problem with initial sugar determinations, added sugar requirements and subsequent alcohol content. Hydrometer readings on the initial crushed fruit may be way off, depending on how well the crush goes. Much could still be locked up in the uncrushed portion, especially on plums, cherries, and other hard to crush fruit. Would destoning, say one pound, and running the pulp through a blender and checking the specific gravity on the strained juice give a fairly accurate sugar content? Should I deduct a certain percentage for non-sugar solids?
Ray Ruthenberg
Galena, IL
Wine Wizard replies: You’ve hit the nail on he head — a hydrometer reading does depend on the amount of suspended solids in the juice that you’re measuring. As sugar is more dense than water, the more sugar (the riper your fruit is) in the juice the higher up the hydrometer will float in your sample. It’s easy to see that if you’ve got lots of little bits of suspended pulp helping the hydrometer to float well above what would be its natural level you’re going to get an artificially high reading. This is why it is so important to measure juice that has as little suspended solids as possible. I don’t recommend you invest in a battery of strainers, settlers and centrifuges. That would be silly because if you follow the tips below you will have juice that is just fine to measure — the extra degree of precision that these tools of paranoia could buy you would be minimal indeed and certainly not worth your time or money.
I always always follows the same procedure when checking my sugars: soak, sample, strain and squeeze. When you receive a load of fresh grapes, cherries, plums or any other fruit that you’re going to ferment, go ahead and crush the fruit in prep for fermentation as you normally would. First you soak. Let the fruit and juice macerate for 12 to 24 hours — this step is key! Freshly-breached cell walls will not release all of their soluble carbohydrates just because you want them to! It takes time. After you’ve waited for the majority of the sugars to be released into the surrounding environment (that’s the juice to you and me), stir up your container (be it a 5-gallon bucket or a 50-gallon drum) and scoop yourself out a nice, sloppy sample, about 3 cups worth. Make sure you’ve stirred it up well beforehand and that you’ve got some of the chunky stuff in there too. Put the whole gloppy mess into a large strainer you’ve lined with 2 or 3 layers of cheesecloth. Strain the liquid out and give the solids in the cheesecloth a very gentle squeeze, just until the juice coming out stops being a steady stream and begins to come out in drops. Being gentle is the key. If you’re forceful, a lot of the solids will find their way out of the cheesecloth bundle into your sample — just what we’re trying to avoid! Similarly, you wouldn’t want to blend up the sample as this would just be mincing the solids up even further, incorporating them even more into the juice, making what for all intensive purposes would be a fruit smoothie — nice, thick and definitely not an accurate representation of the density due to sugar in the juice itself.
At this point you should have enough juice to give you a pretty representative sample which you could go ahead and measure. If you wanted to be particularly accurate (like if you’re going to have to add sugar and you want to know how much to ameliorate) you could then let the sample settle for another 12-24 hours in the refrigerator. We don’t want any spontaneous fermentations happening here! Siphon the clearest juice off of the top and then measure that. When you’re making a wine where you’re just going to be fermenting the juice and not the pulp, you’ll go through a settling stage post-press anyway, so your sample will be more precise. Always be sure to correct hydrometry readings for temperature. Warmer liquids are less dense than colder ones and will always give different density readings even if they’re of the exact same chemical composition.
Refractometers measure the amount of sugar by bending light through a prism in a way that correlates to the refractive properties of the juice. Again, a clear sample will yield the most accurate results. Refractometers are quick and easy, but are expensive. |
| |
| |
|
|
 |
Welcome
to the online home of WineMaker
-
the leading magazine for the
home wine making hobby. Enjoy this selection of stories, tips, projects
and recipes from the magazine as well as web-only features, all
designed to help you make world-class wine at home. Please sign up for
a FREE
trial issue of the magazine if you like what you see. |
|
 |
|
|
|
Sulfite Calculator
Find
out the amount of sulfite to add to your wine with this handy program. |
|
|
|
|
|
|
|
|
WineMaker's Log Chart
Keep
accurate records of each step of every batch of your wine with this
downloadable log chart. |
|
|
WineMakerCasts
Listen
in as WineMaker editors and writers talk about
winemaking and wine! |
 |
|
|
We Want You in WineMaker
In
every issue of WineMaker, we publish a lot of
material that comes straight from home winemakers like you. Let us know
your tips, story ideas, projects, events and more! |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Making wine from a kit
Past
winners of our annual contest featuring the best homemade labels for
homemade wine.
See
the winners of past WineMaker International Wine Competitions, the
largest event of its kind in the world.
